Laboratory switching power supply with adjustable output voltage from 0 to 15 VDC and maximum current of 2 A. It has a short-circuit protection and LCD display with backlight indicating the voltage and current supplied. It keeps the set values reliably and independently of the fluctuations in the supply voltage or the…
Laboratory power supply with double adjustable output in voltage and current (from 0 to 30 VDC / from 0 to 3 A) and fixed output to 5 VDC / 3 A. It has a backlit LCD display to check the voltage and current, voltage and current settings, overcurrent protection, low ripple and…
Laboratory power supply equipped with double adjustable output in voltage and current (from 0 to 30 VDC / from 0 to 5 A) and fixed output to 5 VDC / 3 A. It has a backlit LCD display to display voltage and current, voltage and current settings, overcurrent protection, low ripple and…
Chassis specially designed to make a crawler robot able to move on rough terrain and able to transport a load of about 7 kg. The frame, the gears, the suspension struts, and the wheels are made of aluminum. The upper part of the frame has many fixing holes and some slots for the installation of…
Laser module with blue emission (445 nm) for industrial applications complying with EN60825-1 standards. Each module is tested in continuous output for 200 hours and is subject to 300 ON / OFF cycles. The module has a fan for heat dissipation, allowing the LASER to operate continuously. The module requires a 12 volt supply voltage…
SD Card shield for Arduino Shield for Arduino equipped with SD Card slot and micro SD adapter. It has a communication interface (SPI, I²C, UART), 3.3V and 5V power switch, power status LED, reset button, jumper to set SPI pins (D11, D12 or D13), 4-pin connector for UART interface (RX, TX, VCC, GND) and…
Mercury System, the HW/SW development system for IoT and Connectivity applications developed together with our collaborator Francesco Ficili, is now available on OpenStore. The system uses various type of electronic boards (logic unit, modems, slave boards equipped with sensors and actuators, power boards…) and a complete SW framework to allow the realization of IoT and…
Given two batteries, it chooses the one to connect to the load based on the voltage measured at their poles. It can also be used to switch DC power supplies. The growing demand for portable devices capable of working where there is no power grid or it is not convenient to use it is…
An audio file player based on an MP3 module with FM radio, Bluetooth and remote control; a 10 V stereo output and two speakers are used for the listening. The device can even work via outlet or using two 3.7 V rechargeable lithium batteries. We all know we can find any kind of loudspeakers…
Make use of an ad hoc module by AMS in order to make a precious Arduino based tool. It will allow analysis of materials, including food and drink, through the spectrum obtained with a light stimulus and a sensor, and shown on the serial monitor. Spectrometry is an analysis technique that enables the identification…
Let’s optimize power consumption for our Arduino-like boards using specific hardware solutions and a dedicated software library. We recently had many requests about solutions to reduce power consumption for our Fishino boards, particularly from those – among the designers – who need to activate them for short periods of time: for instance, in…
The latest robot from Waveshare, it adds interesting features to the qualities of its predecessor. You were able to appreciate the instructional robotics platform on wheels called Alphabot, in an article dedicated to it, and you were able to see it in its version with Arduino controller. Alphabot, we remind you, is a robot…
Open-Electronics.org is the brainchild of a world leader in hobby electronics Futura Group srl. Open-Electronics.org is devoted to support development, hacking and playing with electronics: we share exciting open projects and create amazing products!
Open-Electronics.org is not just a container of ideas: it is also a web site lead by a team of engineers and geeks who will take part in the discussions and give support.
Our mission is to become a reference Open Source hacking site with ideas and feedback aimed to enrich the community.
