Ultra-small module (13.3×10.6×3.5 mm) based on the BME280 pressure, humidity and temperature sensor. It is fully calibrated, ready to use and supports I²C and SPI digital interfaces. The I²C interface supports Standard, Fast and High-Speed modes. Power supply: 1.8 VDC to 5 VDC, interfaces: I2C (up to 3.4 MHz) and SPI (3 and 4 wire,…

JT-PIMEDIA is a set that includes of a black acrylic multimedia box and a 4GB Raspberry Pi 4 Model B. The box is made of a semi-transparent central part, an upper and a lower cover that magnetically hook onto the central part, avoiding the use of screws, etc. Inside the box there are two interface…

Set containing all the LASER-cut plexiglass parts and the 3D printed container used in the project “THE FLAME THAT DOESN’T BURN” published in the Elettronica magazine n.239 October 2019. The plexiglass parts are 3 sheets of 3 mm, one hollowed out internally according to the shape of the flame which is the most advanced part…

Addressable light strip with144 high brightness, flexible and weatherproof RGB LEDs (IP67). Each single LED (SMD5050) integrates the control chip (SK6812). Each chip communicates with the next through a line by transferring the information received. These “intelligent” strips therefore lend themselves very well to create borders and contours that light up and color on command;…

This experimental board, made specifically for Arduino Mega, makes the connections of the PA0 ÷ 7 port of the Arduino Mega 2560 available and distributes them via on-board jumper for the management of the digital output lines. It also takes the signals from the PL0 ÷ 7 port of the Mega 2560 to manage the…

Small board able of hosting the ESP8266 Wi-Fi module (not included). It has a 2-way terminal for power input; 4-way terminal with + 5V, ground and the lines IO0 and IO2 (two GPIOs of the U2 module) carrying the data; connector (CN1) with the same signals as the ESP8266 module (TX and RX of the…

Electronic board with 20 miniature Neopixel LEDs (2.4×2.7×1.1 mm) and connectors with power supply pins and communication bus. Suitable for use with Nixiel displays (not included, see related products). Power supply: 5 VDC, dimensions (mm): 57x30x3.5, weight: 5 grams. Attention! the LASER cut plexiglass parts, necessary to complete the Nixiel display, are not included.  …

This kit allows you to create a single display with 7 segments that recall of the fascinating Nixie tubes. It is composed of 10 LASER engraved plexiglass panels with the numbers from 0 to 9, three plexiglass frames (upper, middle and lower) and an electronic board with 20 miniature Neopixel LEDs (2.4×2.7×1.1 mm). Each panel…

Sealed rechargeable battery with a rated voltage of 6 V, 1.3 Ah of capacity and low level of self-discharge. Dimensions: 97 x 24 x 52 mm; Weight: 300 g. Suitable for alarm systems, UPS, toys, etc.   Technical spetifications Rated voltage: 6 V Capacity: 1.3 Ah Weight: 300 g Dimensions: 97 x 24 x 52 mm   Go to…

Sealed rechargeable battery with a rated voltage of 6 V, 3.4 Ah of capacity and low level of self-discharge. Dimensions: 134 x 34 x 62 mm; Weight: 630 g. Suitable for alarm systems, UPS, toys, etc.   Technical spetifications Rated voltage: 6 V Capacity: 3.4 Ah Weight: 630 g Dimensions: 134 x 34 x 62 mm   Go…

Keep social distancing with an audible and optical signal that warns us when we are getting too close to the counter of a shop, a kiosk or a desk. The kit consists of a screen-printed plexiglass panel, a perforated container and all the electronic components to be wired. The device is based on a tiny…

Small module for Raspberry Pi equipped with 5 megapixel camera (Omnivision 5647). It is capable of taking pictures with a resolution of 2592×1944 pixels. The small module, which has dimensions of only 25x24x9 mm and weighs 3 grams, can also shoot HD video in 1080p format at 30 fps, giving the possibility to users of…