1-Motor DC Driver, 40A – 4 Control Modes
€80.33excl. VAT€98.00incl. VATCompact power driver able to control 1 DC motor with a supply voltage between 10 VDC and 45 VDC and a max current
Narrow by category
All
Robotics › Sensors187
Enclosures143
Arduino compatible115
Raspberry Pi115
Breakout boards › Sensors112
Buttons, switches & joysticks109
Actuators100
Soldering100
Arduino94
Resistors86
Displays84
Lab cables83
LEDs83
Light bulbs78
Counts based on the first 4198 matches.
-
Control electronics -
Actuators1-relay module 5 Vdc, low-level trigger (assembled)
€2.05excl. VAT€2.50incl. VATModule with 1 relay, two status LEDs (power and relay), a transistor and a diode
-
Soldering1.3 mm active chisel tip for micro-soldering pencil
€31.97excl. VAT€39.00incl. VAT1.3 mm active chisel tip from the RTM series, for precision micro-soldering. Its built-in heating element brings it up to temperature in about 5 seconds. It fits the WTMP MS micro-soldering pencil of the WT1010M and WT2023M stations, where it is the tip supplied as standard.
-
Power connectors1.3 mm DC Power Plug
€0.25excl. VAT€0.30incl. VATPower plug with a 1.3 mm pin, to be soldered to the end of a power supply lead
-
Displays1.3-inch OLED Display
€9.02excl. VAT€11.00incl. VATBlue OLED (Organic Light Emitting Diode) display, 1.3″
-
Displays1.3” I2C OLED Display – GND/VCC/SCL/SDA
€13.03excl. VAT€15.90incl. VATModule with a 128×64 pixel blue OLED (Organic Light Emitting Diode) display, I²C interface, SH1106 graphic controller, viewing angle approx. 160°
-
Displays1.44 inch TFT Display with ST7735 Driver
€9.43excl. VAT€11.50incl. VAT1.44″ IPS colour LCD display module with a high 128 x 128 pixel resolution and a wide ± 80 degree viewing angle, driven by the ST7735 controller, with SPI interface.
-
Soldering1.5 mm Replacement Tip for TPGSS501 and TIP027
€2.05excl. VAT€2.50incl. VATReplacement tip for the TPGSS501, VTSS4N, TIP027 soldering stations and the TP0055 soldering pencil.
-
Soldering1.6 mm Chisel Soldering Tip, ET Series
€6.56excl. VAT€8.00incl. VAT1.6 mm chisel soldering tip from the ET series, the all-purpose shape for most printed circuit board work. It is compatible with the WEP70 iron and is supplied as standard with the WE1010 station.
-
Soldering1.6 MM TIP FOR VTSSC10N/VTSSC30N/VTSSC40N
€2.05excl. VAT€2.50incl. VAT1.6 mm replacement tip for the VTSSC10N, VTSSC30N and VTSSC40N soldering stations.
-
micro:bit1.8 inch display for MicroBit
€21.31excl. VAT€26.00incl. VATRGB display module with 65K colours designed for use with the micro:bit board, 1.8 inch diagonal, 160×128 pixels
-
Actuators1.8kg/cm Mini Servo Motor, Metal Gears, 180°
€6.56excl. VAT€8.00incl. VATMini servo with metal gears, accessories included
-
Arduino10 A Motor Shield for Arduino
€16.39excl. VAT€20.00incl. VATArduino shield based on an H-bridge made up of 4 NMOS transistors which, besides providing better efficiency, remove the need for a heatsink
-
Sockets & remote sockets10 A Wi-Fi Switch – Amazon Alexa and Google Assistant
€7.79excl. VAT€9.50incl. VATA simple Wi-Fi switch that wires straight onto the 220 VAC mains and can control a load of up to 10 A on its output
-
Lab cables10 cm Cable with Female Tamiya Connector – 25A
€2.38excl. VAT€2.90incl. VATCommonly used with 7.2 V sub-C battery packs, this 10 cm AWG cable is fitted with a female connector (sometimes called Tamiya or Kyosho) designed to prevent reverse polarity, with a latch that prevents it from coming loose from the male connector, and able to handle high DC currents
-
Lab cables10 cm Cable with Tamiya Mini Male Connector
€2.87excl. VAT€3.50incl. VATCommonly used with 7.2 V sub-C battery packs, this 10 cm AWG lead carries a male connector (sometimes called Tamiya or Kyosho) shaped so that the polarity cannot be reversed, with a latch that stops it working loose, and able to carry high DC currents
-
Lab cables10 cm Lead with Male Tamiya Connector – 25A
€2.38excl. VAT€2.90incl. VATCommonly used with 7.2 V sub-C battery packs, this 10 cm AWG lead has a male connector (sometimes called Tamiya or Kyosho) shaped so that reverse polarity is impossible, with a latch that stops it unplugging from the female connector, and able to carry high DC currents
-
Lab cables10 cm lead with Tamiya female mini connector
€2.87excl. VAT€3.50incl. VATCommonly used with 7.2 V sub-C battery packs, this 10 cm 18-AWG lead has a female mini connector (sometimes called a Tamiya or Kyosho) shaped so that the polarity cannot be reversed, with a catch that stops it pulling off the male connector, and it will carry high DC currents.
-
Lab cables10 Colour-Coded Female-to-Alligator Jumper Leads
€3.69excl. VAT€4.50incl. VATRibbon of 10 leads, 20 cm long, terminated with a 1-way male connector at one end and an alligator clip at the other
-
Lab cables10 Coloured Male-to-Crocodile Jumper Leads
€3.69excl. VAT€4.50incl. VATRibbon of 10 leads, 20 cm long, terminated with a 1-pole male connector at one end and a crocodile clip at the other