Micro USB Connector for PCB SMT
5-pin female type USB micro-USB connector. SMT assembly. …. Read more: Micro USB Connector for PCB SMT
-
-
Servo shield
Servo shield for Arduino/Fishino UNO allow to control up to 6 RC servos 3 pins (+5V / – / PWM ) and RC servos 4 pins with feedback (+5V / – / PWM / Feedback ). On board there is a 5 volt 3 A power supply based on chip WP1584, 2 power MOSFET outputs with LED, 1 digital input…
-
3×2 pin female connector
A female connector 3×2 pins pitch 2.54 mm for Arduino …. Read more: 3×2 pin female connector
-
4 DOF Plexiglass Robotic Arm
Kit containing everything you need to make a plexiglas robot arm with 4 degrees of freedom, rotating base (180 °), gripper to grasp the objects and 5 analogue RC servos that can be managed by Arduino or other electronics. The gripper can be mounted either horizontally or vertically and it is able to rotate +/-…
-
Display OLED I2C 0,91" 128×32 pixel
Module with 0.91″ OLED display (Organic Light Emitting Diode), 128×32 pixels, blue color, I²C interface, graphic controller SSD1306, viewing angle> 160°, interfaceable to Arduino. Equipped with good contrast, it does not need backlighting. Power supply: 3,3 to 5 VDC, dimensions (mm): 38,3x12x4, weight: 3 grams, working temperature: from -40°C to +70°C. …. Read more: Display…
-
Demoboard for Arduino
Demoboard specially designed to allow the end user to perform and demonstrate the operation of the circuits made with the ATmega328PU processor in the Arduino environment. The demoboard is based on the compatible Arduino Nano module (included) and allows numerous hardware connections. In this workstation, there is everything you need to learn how to use Arduino,…
-
Raspberry Pi 8-ch Relay Expansion Board
RPi relay board is an expansion board for Raspberry Pi (A+ / B+ / 2B / 3B / 3B+) with DIN rail mounting case, equipped with 8 high quality relays able to support loads up to 5 A 250 VAC and 5 A 30 VDC, an optocoupler for each input, LED…
-
USB to TTL converter
Small USB-TTL converter based on the CP2102 chip. It has a male type A USB connector on one side and a comb connector with DTR, RXD, TXD, + 5VCC, GND and 3.3VCC pins on the other. 5V power supply via micro USB connector. Compatible with Windows XP, 7, 8 to 32…
-
Stepper Motor + Driver
Set consisting of a stepper motor driver based on the ULN2003 chip and a 4-phase stepper motor. Equipped with 4 status LEDs for each phase of the motor, the driver is controlled via the 4 input pins IN1-IN2-IN3-IN4 with Arduino / Fishino or other microcontrollers. Power supply: 5 Vdc – 500 mA, driver dimensions…
-
TCS3200 RGB Color Sensor
This is an Arduino/Fishino RGB Color Sensor breakout uses TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 color sensor can detect and measure a nearly limitless range of visible colors. The TCS3200 has an array of photodetectors, each with either a red, green, or blue filter, or no filter (clear). The filters of each…
-
FM Receiver Module
Based on the chip of the Philips TEA5767, this tiny module allows to realize, with the addition of very few external components, a stereo FM radio with reception frequency from 87.6 MHz to 108 MHz .. Used in MP3 players, MP4, mobile phones, etc. 3.3V @ 11mA 76-108MHz supported 100mV audio output Stereo output…. Read…
-
Thermo-Electric Cooler for Peltier cell 40×40 mm
Heatsink and fan assembly with thermal paste and an aluminum clamp for Peltier Cell. Simply connect to 12V 5A+ power supply and you will see frost appear on the aluminum plate within a minute. Consisting of an aluminum heat sink (80x80x30 mm), an aluminum heat sink (60x45x16 mm), adhesive insulation and an 80×80 mm 12V…
