Screw terminal shield for Arduino
€4.84excl. VAT€5.90incl. VATThe screw terminal shield for Arduino is an expansion board that brings all the input/output and power pins of the Arduino board out to convenient screw terminals.
Narrow by category
All
Robotics › Sensors187
Enclosures143
Arduino compatible115
Raspberry Pi115
Breakout boards › Sensors112
Buttons, switches & joysticks109
Actuators100
Soldering100
Arduino94
Resistors86
Displays84
Lab cables83
LEDs83
Light bulbs78
Counts based on the first 4198 matches.
-
Arduino -
Arduino compatibleMotor Control Shield for Arduino with LM293D
€4.51excl. VAT€5.50incl. VATThe Motor Shield with LM293D is a board for Arduino that drives up to 4 DC motors independently. It handles voltages up to 36V and currents up to 600mA per channel. It carries two L293D drivers and a 74HC595 shift register, cutting the Arduino pins needed for motor direction down to just 3. Suitable for all sorts of projects, from robotics to automation
-
ArduinoBox of 37 sensors for Arduino/Raspberry Pi/robotics
€24.51excl. VAT€29.90incl. VATPack containing 37 sensors for use with the main development platforms
-
Arduino2-Channel DC Motor Speed Control Shield
€11.48excl. VAT€14.00incl. VATArduino shield based on the L298P dual full-bridge driver, able to drive 2 DC motors (or one stepper motor) with a supply voltage between 4.8 and 24 VDC and a current of up to 2 A (2.5 A peak)
-
Arduino compatibleUNO R4 WiFi compatible development board
€22.05excl. VAT€26.90incl. VATUNO R4 WiFi compatible development board with a Renesas RA4M1 MCU, ESP32-S3, USB-C and WiFi/Bluetooth connectivity for IoT projects.
-
Arduino compatibleMaker UNO Plus
€18.44excl. VAT€22.50incl. VATMaker UNO Plus is a development board compatible with the Arduino UNO R3, an alternative and improved solution. Based on the ATmega328P, it has 12 LEDs (from pin 2 to pin 13), 1 piezo buzzer (pin 8), 1 on/off switch for the buzzer, 1 programmable pushbutton (pin 2) and a micro USB connector. The current available for devices running at 3.3 V is a full 500 mA, against the 50 mA of the Arduino Uno. The USB-to-serial converter has been upgraded from the CH340 chip to the FT231X.
-
Arduino compatibleMaker UNO Development Board
€11.39excl. VAT€13.90incl. VATMaker UNO is a development board compatible with the Arduino UNO R3, an alternative and improved solution. Based on the ATmega328P, it has 12 LEDs (pin 2 to pin 13), 1 piezo buzzer (pin 8), 1 on/off switch for the buzzer and 1 programmable button (pin 2).
-
ArduinoLCD keypad shield for Arduino
€10.57excl. VAT€12.90incl. VATShield for Arduino (Uno Rev3, Mega, Duemilanove and Leonardo) with a 16×2 LCD display, white characters, blue backlight, contrast trimmer, 6 buttons (Up, Down, Left, Right, Select and Reset) and pads for an ICSP connector
-
ArduinoShield for PS2 controllers
€23.77excl. VAT€29.00incl. VATThis shield for Arduino (Uno, Duemilanove, Mega and Leonardo), fitted with an Arduino reset button, a jumper to set the Baud Rate (9600, 57600, 115200), a status LED and jumpers to choose different pins for UART TX and RX, lets you use the wireless (or wired) Playstation 2 controller to drive robots or other devices remotely
-
ArduinoShield for G15 Servo Cube
€11.48excl. VAT€14.00incl. VATCompatible with Arduino UNO, Duemilanove, Mega and Leonardo, this shield lets you drive Cytron G15 Servo Cube serial servos and the Dynamixel AX-12 servo
-
ArduinoEL shield for Arduino
€28.69excl. VAT€35.00incl. VATThe EL Shield lets Arduino drive up to 4 electroluminescent strips with an operating voltage of up to 160 Vac; in this configuration the shield can drive strips up to 15 metres long
-
ArduinoBlack enclosure for Arduino Uno
€4.92excl. VAT€6.00incl. VATBlack ABS enclosure made specifically to house an Arduino UNO board, leaving the reset button accessible and allowing shields to be fitted
-
Sale!
Arduino compatibleDevelopment board with ATmega2560
€21.31excl. VAT€26.00incl. VATCompact board built around the Atmega2560 microcontroller
-
ArduinoSensor Shield for Arduino
€9.02excl. VAT€11.00incl. VATThis shield makes it easy to connect modules such as sensors, servos, relays, buttons, potentiometers and more to Arduino
-
STM32 & NucleoBoard with STM32F103C8T6 Microcontroller
€12.13excl. VAT€14.80incl. VATSTM32ARMCORE is a board based on the STM32F103C8T6 microcontroller (LQFP 48-pin case) Cortex-M3
-
DisplaysArduino TFT Touch Screen Shield 3.5”
€26.23excl. VAT€32.00incl. VATShield for Arduino Uno built around a 3.5″ TFT LCD display with resistive touch screen, ILI9486 graphics controller, 480×320 pixel resolution, 65,000 colours, white LED backlight, SD card slot and SPI interface
-
ArduinoArduino TFT touch screen shield 2.8”
€22.95excl. VAT€28.00incl. VATArduino shield made up of a 2.8″ TFT LCD display with resistive touch screen, ST7789V graphics controller, 320×240 pixel resolution, 262,000 colors, white LED backlight, SD card slot and SPI interface
-
DisplaysEPAPERHAT 2.13 inch e-Paper module 250×122
€17.21excl. VAT€21.00incl. VATEPAPERHAT is an e-Paper or Paper Ink (electrophoretic) display with a built-in graphic controller and a connector for use with Raspberry Pi 2B / 3B / 3B+ / Zero / Zero W
-
DisplaysEPAPERUART 4.3 inch e-Paper module 800×600
€72.95excl. VAT€89.00incl. VAT4.3 inch e-Paper or Paper Ink (electrophoretic) display with a resolution of 800 (H) x 600 (V) pixels
-
DisplaysEPAPERUART 2.9 inch e-Paper module 296×128
€20.49excl. VAT€25.00incl. VATe-Paper or Paper Ink display (electrophoretic), active matrix TFT