Light intensity sensor
€3.44excl. VAT€4.20incl. VATVery small breakout based on the BH1750FVI ambient light sensor
Robotics & development
784 products
Narrow by category
-
Sensors -
SensorsLight Sensor Module with LDR, 3-Pin Output
€2.46excl. VAT€3.00incl. VATAnalogue sensor with a light-dependent resistor and a 3-pin output connector, 2.54 mm pitch.
-
RobotsLight-Seeking Crawling Robot Kit – Microbug
€18.03excl. VAT€22.00incl. VATMiniature insect-shaped robot with a plastic enclosure: it looks for light and always runs towards it, two subminiature motors drive the robot, LED eyes show which way the robot is pointing, and it stops in total darkness.
-
SensorsLightning Sensor Breakout Board – assembled
€20.49excl. VAT€25.00incl. VATBreakout board built around the AMS AS3935 chip, able to pick up the radio-frequency disturbance caused by an electrical arc and, through suitable processing, deliver a signal corresponding to the detection of a lightning strike and its intensity. All the signals needed to drive the chip are brought out to a row of 2.54 mm pitch pads along one edge
-
SensorsLine Sensor
€6.15excl. VAT€7.50incl. VATLine sensor made up of 5 high-sensitivity reflective photointerrupters
-
ActuatorsLinear Actuator 12 V 100 kg – 50 mm Stroke
€65.57excl. VAT€80.00incl. VATBuilt around a 12 Vdc geared motor, it uses a worm screw to move a shaft back and forth along its length, with a maximum travel of 50 mm
-
ActuatorsLinear Actuator 12 VDC 100 kg – 450 mm Stroke
€77.87excl. VAT€95.00incl. VATBuilt around a 12 VDC gearmotor, it uses a lead screw to move a shaft back and forth along its length, with a maximum travel of 450 mm
-
ActuatorsLinear actuator 24 V 100 kg – 50 mm stroke
€65.57excl. VAT€80.00incl. VATBuilt around a 24 VDC geared motor, it uses a worm screw to move a shaft back and forth along its length, with a maximum travel of 50 mm
-
ActuatorsLinear actuator 24 VDC 100 kg – 450 mm stroke
€77.87excl. VAT€95.00incl. VATBuilt around a 24 VDC gearmotor, it uses a lead screw to move a shaft back and forth along its length with a maximum travel of 450 mm
-
SensorsLiquid Level Controller
€5.74excl. VAT€7.00incl. VATThis compact board, combined with two level sensors and a water pump (not included), automatically controls the water level in a tank, cistern, etc
-
SensorsLiquid Level Sensor – 200 mm
€10.66excl. VAT€13.00incl. VATMade of stainless steel and fitted with a float, it is used to detect the level of a liquid inside a tank and can switch on a pump, a warning lamp, an alarm or another device
-
SensorsLiquid Level Sensor – 45 mm
€4.92excl. VAT€6.00incl. VATMade of stainless steel and fitted with a float, it is used to detect the level of a liquid inside a tank and can activate a pump, an indicator light, an alarm or another device
-
SensorsLiquid Level Sensor Board – 48 mm sensing depth
€3.69excl. VAT€4.50incl. VATImmersed in a liquid it returns a voltage proportional to the level, down to a depth of 48 mm; it runs on 2 to 5 Vdc.
-
Sensors -
SensorsLM35DZ – Analog Temperature Sensor
€2.38excl. VAT€2.90incl. VAT3-pin analog temperature sensor (TO-92 case)
-
ArduinoLoad Cell Shield
€18.85excl. VAT€23.00incl. VATDesigned to be paired with an Arduino board and a load cell (not included), it lets you build a scale that reads your weight. That reading can then be processed as you wish and shown on the on-board display.
-
SensorsLoad Cell Type “S” – 1 Ton Range
€52.46excl. VAT€64.00incl. VATType “S” load cell made of stainless steel, precision class C3, 1 ton range and two M12 threaded holes
-
AccessoriesLong “U” Bracket for the G15 Cube Servo
€4.02excl. VAT€4.90incl. VATLong “U” bracket that, paired with the G15 Cube Servo, lets you build moving joints for robots, such as robotic arms with several articulations, etc
-
Raspberry PiLoRa HAT for Raspberry Pi – 433 MHz
€27.87excl. VAT€34.00incl. VATDesigned to work with Raspberry Pi and based on the SX1268 module at 433 MHz, the LoRa HAT provides two-way data transmission up to 5 km over the serial port. It supports automatic retransmission, low-power modes such as deep sleep and Wake on Radio (ideal for battery-powered applications), wireless parameter configuration, RSSI signal strength indication and the LBT function, which can be used to avoid interference. It has a 40-pin GPIO connector for Raspberry Pi, a CP2102 chip for serial debugging, a UART control port for connecting host boards such as Arduino / STM32 and 4 status LEDs: UART RXD and TXD, AUX and PWR.
-
Raspberry PiLoRa HAT for Raspberry Pi – 868 MHz
€34.43excl. VAT€42.00incl. VATDesigned to be used with Raspberry Pi and based on the SX1262 module at 868 MHz, this LoRa HAT provides two-way data transmission over a range of up to 5 km through the serial port. It supports automatic repeating, low-power features such as deep sleep and Wake on Radio (ideal for battery-powered applications), wireless parameter configuration, RSSI signal strength indication and the LBT function, which can be used to avoid interference. It features a 40-pin GPIO connector for Raspberry Pi, a CP2102 chip for serial debugging, a UART control port for connecting host boards such as Arduino / STM32 and 4 status LEDs: UART RXD and TXD, AUX and PWR.