20 A current sensor
€4.84excl. VAT€5.90incl. VATBuilt around the Allegro ACS712ELCTR-20A-T chip, this current sensor reads AC or DC currents between 0 and 20 A
Robotics & development
784 products
Narrow by category
-
Sensors -
Lab cables20 cm Male-Female 40-Way Flat Cable
€1.64excl. VAT€2.00incl. VATFlat cable approximately 20 cm long, with a 2×20 pin male connector on one end and a 2×20 pin female connector on the other
-
Sensors20 kg load cell
€5.74excl. VAT€7.00incl. VATLoad cell made up of a metal body and small elements called strain gauges bonded at precise points on that body
-
Sensors25 VDC Voltage Sensor
€1.23excl. VAT€1.50incl. VATBuilt around a voltage divider with two resistors, this voltage sensor scales the incoming voltage down by a factor of 5
-
Motors3 – 6 Vdc 300 mA Motor – 15000 rpm
€1.07excl. VAT€1.30incl. VATMiniature general-purpose electric motor, 3 – 6 Vdc / 300 mA.
-
Sensors3-axis accelerometer
€4.51excl. VAT€5.50incl. VATDigital 3-axis accelerometer based on the Freescale MMA8452Q sensor
-
Sensors3-Axis Accelerometer + 3-Axis Gyroscope
€7.38excl. VAT€9.00incl. VATSmall board based on the InvenSense MPU-6050 sensor, which contains a 3-axis MEMS gyroscope and a 3-axis MEMS accelerometer
-
Sensors3-Axis Accelerometer with ADXL345
€4.02excl. VAT€4.90incl. VATAnalog 3-axis accelerometer based on the ADXL345 chip by Analog Devices
-
CNC accessories3-axis board set + accessories
€61.48excl. VAT€75.00incl. VATBased on the Toshiba TB6560AHQ chip, it can drive up to 3 bipolar or unipolar stepper motors at 3 A (3.5 A peak)
-
Accessories3-Blade Propeller for Motors
€1.56excl. VAT€1.90incl. VAT3-blade propeller, 40 mm diameter, with a centre hole for motors with a 2 mm shaft
-
IoT (Internet of Things)3-Channel Neopixel Board for the Mercury System
€11.48excl. VAT€14.00incl. VAT3-channel board that interfaces with Neopixel LED strips or rings
-
Raspberry Pi3-Channel Relay Board for Raspberry Pi
€15.57excl. VAT€19.00incl. VATThe RPi relay board is a compact add-on for the Raspberry Pi (A+ / B+ / 2B / 3B / 3B+) with 3 high-quality relays rated for loads up to 250 VAC/5 A and 30 VDC / 5 A, one optocoupler (PC817) per input, LEDs showing relay and power status, and 3 jumpers that let you drive the relays straight from the Raspberry Pi or from another device
-
Robots3-in-1 Educational Solar Robot Kit – Dinosaur, Insect and Drill
€12.30excl. VAT€15.00incl. VATEducational kit for 3 different solar robots: dinosaur, insect and drill.
-
ESP8266 / ESP323.5″ Parallel TFT Display with ESP32-S3
€72.95excl. VAT€89.00incl. VAT3.5-inch TFT display with a capacitive touch screen, ILI9488 graphics controller, ESP32-S3 module and SD card slot.
-
Displays3.5″ Touch Display for Raspberry
€26.23excl. VAT€32.00incl. VAT3.5″ color TFT LCD display for Raspberry Pi
-
Control electronics30A Speed Controller for Brushless Motors
€12.30excl. VAT€15.00incl. VATSpeed Controller for Brushless Motors. Ideal for drones, model aircraft and radio-controlled vehicles. Maximum current capacity 30A. 2-4S LiPo BEC at 5V/2A. Voltage range 4V-16V.
-
Linux embedded4 GB Debian Micro SD Card for Arietta G25
€10.00excl. VAT€12.20incl. VAT4 GB Micro SDHC memory card with a Debian Linux distribution preinstalled for the Arietta-G25
-
Actuators4 relay module 5 Vdc 10A (assembled)
€9.02excl. VAT€11.00incl. VATModule with 4 relays for switching the load connected to them on and off, 240V/10A (max)
-
Infrared4-channel IR receiver with remote control
€5.74excl. VAT€7.00incl. VATSet consisting of an IR remote control and a 4-channel momentary receiver
-
Sensors4-Direction Tilt Sensor
€4.02excl. VAT€4.90incl. VATTilt sensor capable of detecting movement direction in four directions: forward, backward, left, right