Me Uno Shield
€12.30excl. VAT€15.00incl. VATPaired with an Arduino Uno Rev3, this shield lets you use every Makeblock module with an RJ25 (6P6C) interface
Robotics & development + Control electronics
61 products
Narrow by category
-
Control electronics -
Control electronicsMEMS TECHNOLOGY ACCELEROMETER
€3.69excl. VAT€4.50incl. VATExtremely small three-axis accelerometer (just 3mm x 5mm x 1mm) made by Freescale
-
Control electronicsMicro Driver for 2 DC Motors
€4.51excl. VAT€5.50incl. VATBased on the DRV8833 chip, an equivalent of the Toshiba TB6612FNG driver, this compact driver controls 2 DC motors with a constant current of 1.2 A (2 A peak per motor). The two input signals (IN1 and IN2) let you drive each motor in one of four operating modes: forward, reverse, stop, short brake
-
Control electronicsMini Driver for DC and Stepper Motors
€3.20excl. VAT€3.90incl. VATCompact driver that lets you control two DC motors or one 4-wire bipolar stepper motor
-
Control electronicsMini PWM generator with display
€5.33excl. VAT€6.50incl. VATWith its backlit LCD display, this compact module generates a square-wave PWM signal from 1 Hz to 150 kHz with a duty cycle adjustable from 0 to 100%. All the settings, entered with the 4 buttons or over a TTL-level serial link, are saved automatically in non-volatile memory
-
Control electronicsOpen Motor Control – assembled
€27.87excl. VAT€34.00incl. VATBuilt around the ATmega32U4 microcontroller, this module can drive 2 DC motors or 1 stepper motor
-
Control electronicsOpen Source quadcopter board
€28.69excl. VAT€35.00incl. VATBoard based on Arduino Mega that drives the motors of a quadcopter, takes commands from a model-aircraft radio control and supports telemetry over a smartphone
-
Control electronicsPair of Magnetic Encoders for Micro Metal Gearmotors
€12.70excl. VAT€15.50incl. VATMade up of two very small boards carrying two dual-channel Hall effect sensors and two 6-pole magnetic discs, this kit adds a quadrature encoder to micro metal gearmotors (not included) with extended shafts
-
Control electronicsPWM generator for stepper motor drivers
€15.98excl. VAT€19.50incl. VATPulse generator built to interface with the common types of stepper motor controller
-
Control electronicsRC servo pulse to digital converter
€8.11excl. VAT€9.90incl. VATThis small board converts the pulses of an RC radio control (the modelling kind) into on/off signals
-
Control electronicsReed switch module with LM393
€2.05excl. VAT€2.50incl. VATCompact module based on the LM393 chip, fitted with a reed contact (single normally open contact), a sensitivity adjustment trimmer and status LEDs for power and output signal
-
Control electronicsSerial driver for DC motors
€22.95excl. VAT€28.00incl. VATMotor driver (kit), interfaced to a microcontroller’s serial port, can independently control up to 2 DC motors at 1 A each (forward, reverse and speed control in 127 steps)
-
Control electronicsSingle DC Motor Driver 6-27V – 43 A
€9.02excl. VAT€11.00incl. VATDriver for bidirectional control of one DC motor with a supply voltage between 6 and 27 VDC and a current of 43 A
-
Control electronicsSpeed Controller for 1 DC Motor 6-90 V 8A
€6.97excl. VAT€8.50incl. VATCompact board that lets you adjust the speed of a DC motor, with a supply between 6 V and 90 V and a maximum current of 8 A (15 A peak), by means of a potentiometer
-
Control electronicsStepper Motor Control Board with DRV8825 and ATmega32U4
€27.87excl. VAT€34.00incl. VATControl board for stepper motors with a DRV8825 driver and an ATmega32U4 microcontroller for open-loop control of stepper motors, programmable with the Arduino IDE.
-
Control electronicsStepper motor driver up to 3.5 A
€14.75excl. VAT€18.00incl. VATBased on the TB6600,, chip, this compact driver can control a single bipolar stepper motor with a max. current
-
Control electronicsStepper Motor Driver up to 3A with TB6560
€12.30excl. VAT€15.00incl. VATBuilt around the TB6560AHQ chip, this compact driver can drive a single bipolar stepper motor with a max current
-
Control electronicsStepper motor driver up to 5 A
€22.13excl. VAT€27.00incl. VATBased on the TB6600HG chip, this compact driver can control a single bipolar stepper motor with a max. current
-
Control electronicsTX+RX Module Pair for Wireless Charging
€10.66excl. VAT€13.00incl. VATMade up of a transmitter module and a receiver module, it transfers power without cables
-
Control electronicsUSB Board for 1 Stepper Motor – Kit
€35.25excl. VAT€43.00incl. VATConnected to a PC USB port and driven by its own software (a free download), this board controls the movement of a single bipolar stepper motor at a current of 750 mA (1 A peak)