Clear Case for micro:bit
€4.02excl. VAT€4.90incl. VATClear protective case made of 2 mm plexiglass, sized to house a micro:bit
Narrow by category
All
Robotics › Sensors187
Enclosures143
Arduino compatible115
Raspberry Pi115
Breakout boards › Sensors112
Buttons, switches & joysticks109
Actuators100
Soldering100
Arduino94
Resistors86
Displays84
Lab cables83
LEDs83
Light bulbs78
Counts based on the first 4198 matches.
-
micro:bit -
Lab cablesPack of 50 Female-to-Female Jumper Wires – Assorted Colours
€4.10excl. VAT€5.00incl. VATPack of 50 jumper wires in assorted colours, 10 cm long, fitted at each end with a 1-pole female connector
-
Control electronicsJPEG Trigger shield for JPEG UART camera
€27.05excl. VAT€33.00incl. VATMakes the JPEG colour micro camera with UART interface (7300-JPEGCAMERA) simpler to use
-
Raspberry Pi868MHz LoRa Board for Raspberry Pi
€23.77excl. VAT€29.00incl. VATSingle-channel 868 MHz LoRaWAN board, HAT type (Hardware Attached on Top) for Raspberry Pi, based on the RTX 868 MHz Long Range LoRa module (RFM95-868)
-
SensorsSharp Infrared Distance Sensor 4-30 cm – GP2Y0A41SK0F
€13.11excl. VAT€16.00incl. VATInfrared sensor able to detect an obstacle at a distance between 4 and 30 cm
-
SensorsSHARP GP2Y0A02YK IR Distance Sensor 20-150 cm
€13.11excl. VAT€16.00incl. VATInfrared sensor able to detect an obstacle at a distance of between 20 and 150 cm
-
mbed modulesMBED NXP LPC1768 Development Board
€70.49excl. VAT€86.00incl. VATMBED is a board based on the 32-bit ARM® Cortex™ NXP LPC1768 microcontroller running at 96 MHz
-
Mounting systemsMagnet with Centre Hole – 4.74 mm Diameter
€1.80excl. VAT€2.20incl. VATTiny magnet (4.74 diameter x 1.57 mm thick) made of Neodymium / Iron / Boron (NdFeB)
-
CommunicationBidirectional Logic Level Converter
€2.46excl. VAT€3.00incl. VATSmall board that converts logic levels from 5 V to 3.3 V and the other way round (it also works with 2.8 V and 1.8 V devices)
-
Sale!
Linux embeddedRJ45 and USB Board for LININO ONE
€10.66excl. VAT€13.00incl. VATSet for Linino one made up of the “dogRJ45” and dogUSB modules
-
Special functionsDC motor driver IC (SMD)
€4.51excl. VAT€5.50incl. VATThe Sanyo LB1836M chip has two independent H-bridges
-
ActuatorsWheel for GM2 / GM3 / GM9 gearmotors
€1.64excl. VAT€2.00incl. VATRigid plastic wheel designed specifically for the GM2, GM3 and GM9 gearmotors
-
CNC accessories2-Flute End Mill 6mm – 6mm Shank
€26.23excl. VAT€32.00incl. VAT2-flute end mill made specifically for aluminium and plastics
-
SensorsInfrared sensor 38 kHz
€2.30excl. VAT€2.80incl. VATInfrared sensor with amplifier, demodulator and filter tuned to 38 kHz
-
SensorsWaterproof temperature sensor with DS18B20
€19.26excl. VAT€23.50incl. VATBuilt around the Maxim DS18B20 digital temperature sensor, this fully sealed probe measures temperature accurately (from -55°C to +125°C) in wet environments
-
AccessoriesPlexiglass Rotating Base for Stepper Motor (motor not included)
€24.18excl. VAT€29.50incl. VATLASER-cut plexiglass rotating base
-
Electronic components12 Vdc Vacuum Pump
€29.51excl. VAT€36.00incl. VATIt moves 9 to 15 litres a minute and pulls down to 16 inches of mercury, with five hours of continuous running allowed.
-
Access control -
Raspberry PiStarter Kit for Raspberry Pi Zero W
€32.70excl. VAT€39.90incl. VATSet containing the Raspberry Pi Zero W board and its official Raspberry Pi Zero case, a USB/microUSB cable with a switch, an HDMI cable, a 2 X 2.54 pitch header and an HDMI/miniHDMI adapter.
-
Other alternative energyMini Hydroelectric Generator – 9.8 to 15 Vdc output
€11.48excl. VAT€14.00incl. VATFitted into a half-inch pipe it delivers 128 to 260 mA, with a water flow between 1.5 and 20 litres per minute.