Flat stepper motor – 0.8 A
€28.69excl. VAT€35.00incl. VAT4-wire bipolar flat stepper motor
Narrow by category
All
Robotics › Sensors187
Enclosures143
Arduino compatible115
Raspberry Pi115
Breakout boards › Sensors112
Buttons, switches & joysticks109
Actuators100
Soldering100
Arduino94
Resistors86
Displays84
Lab cables83
LEDs83
Light bulbs78
Counts based on the first 4198 matches.
-
Motors -
Sensors“S” Type Load Cell – 500 kg Range
€52.46excl. VAT€64.00incl. VATStainless steel “S” type load cell, C3 accuracy class, 500 kg range and two M12 threaded holes
-
Sensors“S”-type load cell, 200 kg range
€52.46excl. VAT€64.00incl. VATS-type load cell made of stainless steel, C3 accuracy class, 200 kg range and two M12 threaded holes
-
Sensors“S” type load cell – 100 kg range
€52.46excl. VAT€64.00incl. VATStainless steel “S” type load cell, C3 accuracy class, 100 kg range and two M12 threaded holes
-
Electronic componentsElectromagnet Breakout Board
€8.03excl. VAT€9.80incl. VATElectromagnet with a holding force of up to 25 newtons, about 2.5 kg, driven by a single logic pin and powered from 3.3 to 5 Vdc.
-
DC/DC convertersLaboratory Power Supply 0 to 60 V – 6 A – KIT
€195.90excl. VAT€239.00incl. VATKit made up of a 0-60 Vdc 6 A laboratory power supply module with a 2.4-inch LCD display, a metal enclosure, a 220 Vac–60 Vdc 6 A switching power supply and a WLAN module that lets you control the supply from the “RdPower“ app for Android and iOS.
-
EnclosuresAluminium Case for Raspberry Pi 4 – Black
€8.93excl. VAT€10.90incl. VATSturdy black brushed-aluminium enclosure, pre-machined to house the Raspberry Pi 4. It has cut-outs for the various USB, Ethernet, HDMI connectors, etc.
-
DC/DC convertersDC-DC Step-Down Module 5V 3A
€2.05excl. VAT€2.50incl. VATStep-down DC/DC converter with a particularly compact footprint (22.3x17x4.4 mm), able to convert a DC input voltage between 7 and 28 volts into a fixed 5-volt output
-
Displays16×2 LCD display with pre-soldered pin header
€4.92excl. VAT€6.00incl. VATLCD display with pre-soldered pin header
-
ESP8266 / ESP32ESP8266 Wi-Fi Shield for Arduino
€13.11excl. VAT€16.00incl. VATAdds 2.4 GHz Wi-Fi connectivity to Arduino Uno and Mega through the ESP-12F module, with on-board TCP/IP stack and AT commands.
-
ESP8266 / ESP32ESP8266 Debugger Adapter
€4.84excl. VAT€5.90incl. VATBased on the CP2014 USB-to-TTL converter chip, this adapter lets you upload firmware or Arduino code to the ESP8266 Wi-Fi module (not included, see related products)
-
ESP8266 / ESP323.5″ Parallel TFT Display with ESP32-S3
€72.95excl. VAT€89.00incl. VAT3.5-inch TFT display with a capacitive touch screen, ILI9488 graphics controller, ESP32-S3 module and SD card slot.
-
Interface convertersUSB to Serial Converter with CP2104
€6.39excl. VAT€7.80incl. VATCompact USB to serial converter (TTL level) based on the CP2104 chip
-
SensorsAir quality sensor breakout board – SGP30
€15.98excl. VAT€19.50incl. VATBuilt around the Sensirion SGP30 air quality sensor, this very small breakout board reports the carbon dioxide concentration (telling you how stale the air in a closed room is) and the TVOC (Total Volatile Organic Compounds), that is the concentration in parts per billion of airborne particles
-
RF transmitters433 MHz RF TX+RX Module Set
€2.05excl. VAT€2.50incl. VATSet consisting of an SMD 433.92 MHz transmitter module and a receiver module
-
DC/DC convertersAdjustable DC-DC Step-Down Module 4.5-28 V 3 A
€2.05excl. VAT€2.50incl. VATStep-Down DC/DC converter with a particularly compact footprint (22.3x17x4.4 mm), able to convert a DC input voltage between 4.5 and 28 volts into an adjustable output voltage between 0.8 and 25 volts
-
Ethernet devicesMini Ethernet Board with W5500 chip
€12.70excl. VAT€15.50incl. VATUltra-compact module based on the WIZnet W5500 Ethernet chip, with a 32 Kbyte internal memory buffer, an Ethernet connector complete with magnetics and 2 status LEDs (Full/Half duplex, Link, Speed, Active). Supports up to eight simultaneous socket connections
-
ESP8266 / ESP32Maduino Zero ESP8266 Wi-Fi IoT board
€15.98excl. VAT€19.50incl. VATMaduino Zero ESP is an IoT (Internet of Things) solution based on the Atmel 32-bit SAMD21 microcontroller and on the ESP-12S Wi-Fi module built around the ESP8266 SoC (System on Chip). It complies with the 802.11 b/g/n standard at 2.4 GHz and features an integrated TCP/IP stack, 19.5 dBm output power, data interfaces (UART / HSPI / I2C / I2S / Ir Remote Control GPIO / PWM) and an on-board PCB antenna
-
Arduino compatibleATmega328 Board with 868 MHz LoRa
€25.41excl. VAT€31.00incl. VATMaduino is an Arduino-compatible board built around the ATmega328 microcontroller (with the Arduino Pro Mini 3.3V – 8 MHz bootloader) and an on-board LoRa™ RFM95W module at 868 MHz. It uses a CP2104 chip as its USB-to-serial converter, comes with a small external antenna with a UFL connector, and has a reset button plus four jumpers for selecting which digital I/O pins of the RFM95W module (DIO0→D2 / DIO1→D6 / DIO2→D7 / DIO3→D8) are wired to the microcontroller. To program it from the IDE, select the board: ATmega328 (3.3V, 8 MHz)
-
Raspberry PiRTC Module for Raspberry Pi
€4.84excl. VAT€5.90incl. VATReal Time Clock module designed specifically for use with the Raspberry Pi